Under Slab Pipe Replacement Victoria TX means cutting out the failed line beneath your foundation and putting in new pipe that will not leak again. We handle below slab pipe replacement Victoria Texas homeowners call about most: hot spots on the floor, a water bill that doubled, or a sewer smell that will not quit. We locate the break, tunnel to it, swap the pipe, and pour the slab back.
Under Slab Pipe Replacement Victoria TX is the removal and replacement of water, drain, or sewer lines buried beneath your concrete foundation. We start with electronic leak detection equipment and a RIDGID SeeSnake camera to map the run and confirm whether the pipe is worth saving. If it is not, we cut a clean access point with a concrete saw, tunnel under the slab instead of demolishing the whole floor, and pull the failed copper, cast iron, or galvanized pipe out.
Victoria sits on expansive clay soils that shift with every wet and dry cycle, and that movement is hard on older lines. A pinhole leak in a 1970s copper line can soak the soil under your slab for months before you see water pooling on the floor. When you search for under slab pipe replacement near me Victoria, you want a crew that reads those signs fast. We run pressure testing gauges and moisture meters before we quote anything.
Every job includes the full scope from detection through concrete restoration. You are not coordinating three different contractors. We handle the locating, the tunneling, the pipe work, the testing, and the patch. Add-ons like foundation assessment or full sewer line replacement are quoted separately if we find they are needed.
We use acoustic listening devices, thermal imaging, and a RIDGID SeeSnake to confirm the failure point and the pipe's condition. You get a written summary of what we found and what we recommend before any cutting starts.
We cut the smallest access points needed with a concrete saw and tunnel under the slab with proper shoring. Debris is removed and hauled off. This is what keeps your flooring and furniture intact during the job.
We install new copper or PEX for supply lines and PVC for drain and sewer runs, using proper couplings and pipe sealant. Every joint is made to code and checked as we go. Old pipe is removed completely, not left in the trench.
New supply lines are pressure-tested at 80 psi and held to confirm no leaks. Drain and sewer lines get a camera pass to verify grade and flow. You see the results before we backfill anything.
We backfill, compact, and pour concrete patch mix over the openings, then finish the surface to blend with your existing slab. Most patches are walkable in 24 to 48 hours. We clean the work area before we leave.
You get a written summary of what was replaced and the pressure-test results.
We bring in acoustic listening devices, thermal imaging cameras, and a RIDGID SeeSnake to pinpoint the failure and see the pipe's condition from the inside. You get a straight answer on whether repair or replacement is the right call. This visit usually takes 60 to 90 minutes.
We mark the tunnel path and access points so we cut the least concrete possible. For most Victoria homes that means 2 to 4 openings instead of tearing out a whole hallway. You see the plan and the price before we start cutting.
Using trenchless tunneling equipment and a concrete saw, we open the slab, dig under it, and cut out the failed pipe. A typical residential run takes one to two days. We shore the tunnel as we go and keep the work area contained.
New PEX or copper goes in with proper couplings and pipe sealant, then we pressure test the line at 80 psi and hold it. If it does not hold, we find out now, not after the concrete is back. Sewer runs get a camera pass to confirm flow.
We backfill, compact, and pour concrete patch mix over the openings, then finish the surface to match. Most patches are walkable in 24 to 48 hours. You get a final walkthrough of the work.
We bring in acoustic listening devices, thermal imaging cameras, and a RIDGID SeeSnake to pinpoint the failure and see the pipe's condition from the inside. You get a straight answer on whether repair or replacement is the right call. This visit usually takes 60 to 90 minutes.
Video pipe inspection that shows us the inside of the line, so we know whether it is a spot repair or a full replacement before we cut.
Detects temperature differences on the floor to locate hot water line leaks without opening the slab first.
Amplifies the sound of pressurized water escaping a pipe, letting us pin the leak to within inches.
Maps the exact path of under-slab lines so our access points land on the pipe, not beside it.
Confirms the new line holds at 80 psi before we backfill and patch. No guesswork.
Lets us work under the slab from small access points instead of demolishing the whole floor.
Under-slab pipe failures show up in a handful of ways, and every one of them gets worse if you wait. Here are the problems we fix most often in Victoria County.
Ask a pro →We locate the leak with acoustic and thermal gear, confirm whether the line is repairable, and replace it if the pipe is failing. Pressure testing after install confirms the new line holds. Most customers see their bill normalize within one billing cycle.
We trace the hot water run with thermal imaging, pinpoint the failure, and replace the damaged section or the full run. New PEX or copper goes in, gets tested, and the slab is patched. The hot spot disappears once the leak is gone.
We camera the line, find the break, and replace the damaged section with new PVC. Grade and flow are verified before we close up. If the whole run is failing, we quote full sewer line replacement in the same visit.
We inspect the full run with a camera and assess the pipe's condition. If it is widespread, we replace the line in one job instead of chasing leaks. That is usually cheaper over two years than three separate repairs.
We locate the failed line with acoustic and thermal detection, cut small access points in the slab, tunnel underneath, and pull the old pipe out. New PEX or copper goes in, gets pressure-tested at 80 psi, and the concrete is patched. Most residential jobs take two to four days from start to walkable floor.
It is the full swap-out of a water, drain, or sewer line buried under your foundation, not a patch. We remove the corroded section and install new pipe along the same run. It is the right call when a line has leaked more than once or when a camera shows widespread corrosion inside the pipe.
Most Victoria jobs run $3,500 to $12,000 in 2026, depending on run length, pipe material, and how many access points we need. A single bathroom line sits at the low end; a full main replacement with multiple tunnels sits higher. You get a fixed quote before we cut anything.
Replace when a line has leaked twice in the same run, when a camera shows heavy corrosion in galvanized or cast iron, or when your water bill jumps and stays high. If you see hot spots on the floor or hear water running with everything off, call us for a leak check that day.
If you have a hot spot on the floor, a climbing water bill, or a sewer smell you cannot trace, call us. We locate the problem, give you a fixed price, and get the line replaced right. Available 24/7 for emergencies.
Get a Free Quote 83157330144 →Call us at 831-573-30144 any time, day or night. We answer emergency calls 24/7 and schedule standard appointments Monday through Friday. If you're not sure whether you have a slab leak, call anyway and we'll help you figure out the next step.