Camera scoping and diagnosis
A RIDGID SeeSnake video inspection of the full run, recorded and shown to you on site. You see the corrosion, the pinholes and the pipe condition before we quote anything.
Rebuild corroded under-slab pipes from the inside, no demolition
Epoxy pipe lining Victoria TX that skips the jackhammer
Epoxy pipe lining Victoria TX restores corroded copper, cast iron and galvanized lines from the inside out, so you keep your floors and your landscaping. If a slab leak has you watching the water bill climb, epoxy pipe coating in Victoria Texas scopes the line, cleans it, and cures a structural coating that seals pinholes and slows future corrosion. Most homes are back to normal the same day.
Careful work. Honest options.
About this service
What epoxy pipe lining Victoria TX actually does
Epoxy pipe lining Victoria TX is a trenchless rehabilitation method that rebuilds a failing water or drain line from the inside. We feed a flexible liner saturated with two-part epoxy through an existing pipe, inflate it against the walls, then cure it with heat or ambient air until it hardens into a smooth, seamless tube inside the old pipe. The original copper, PVC or cast iron stays where it is; the new epoxy wall carries the water. A typical residential run of 20 to 40 feet cures in three to six hours, and the line is ready for pressure testing the same day.
Victoria homes built before the 1980s are the usual candidates. Our soil swings between shrink-swell clay and sandy loam, and that movement flexes under-slab copper until pinhole leaks open up. Homeowners in 77901 and 77905 often call us after a jump of 8,000 to 15,000 gallons on a single billing cycle, or after finding warm spots on a hallway floor. If you have been searching for epoxy pipe lining near me Victoria, this is the repair that fixes the pipe without cutting a trench through your slab.
- ✓ No slab demolition
- ✓ Stops pinhole leaks for good
- ✓ Lower cost than repiping
- ✓ One-day turnaround
What's included
What our epoxy pipe lining service includes
Every lining job we quote covers the full scope from diagnosis to restored floor. We do not hand you off to a concrete contractor or leave you chasing a patch crew. One price, one crew, one point of contact from the first camera run to the final pressure test.
Access point cutting
Two clean 18-inch openings cut with a concrete saw, plus jackhammer work where the slab is reinforced. We lay drop cloths, contain the dust, and haul all debris out the same day.
Pipe cleaning and prep
Mechanical scraping and high-pressure water to strip scale, rust and biofilm down to bare pipe wall. This is the step that decides how well the epoxy bonds, so we do not rush it.
Epoxy liner installation and cure
Two-part epoxy-saturated liner pulled through the pipe, inflated against the walls, and heat-cured for three to six hours. We monitor cure temperature with a Fluke probe the whole time.
Pressure testing and camera verification
A 100 psi pressure test plus a final camera pass to confirm the seal and full flow. You get the results before we close anything up.
Concrete patch and restoration
Access points filled with concrete patch mix and finished to match the surrounding surface as closely as possible. We clean the work area before we leave.
How it works
How our epoxy pipe lining process works
We start with acoustic listening devices and a RIDGID SeeSnake video camera to confirm exactly where the failure is and how far the corrosion runs. Thermal imaging cameras from FLIR pick up hot spots on the floor that point to a supply-side leak. This stage usually takes 60 to 90 minutes, and it tells us whether lining is the right call or whether the pipe is too far gone.
We shut off the main, drain the affected run, and open two small access points at each end. On slab work that means a concrete saw and, where needed, a jackhammer for a clean 18-inch opening. You will hear cutting for 30 to 45 minutes. We lay drop cloths and haul the debris out the same day.
A mechanical scraper and high-pressure water push out scale, rust and biofilm until the inside wall is bare metal or bare plastic. This is the step that decides how well the epoxy bonds. We run the camera back through to verify the surface is clean before we ever mix resin.
We saturate the liner with two-part epoxy, pull it through the pipe, and inflate it against the walls. Heat cures the resin in three to six hours depending on diameter and length. A 1.5-inch line cures faster than a 4-inch sewer branch, and we monitor temperature the whole time with a Fluke probe.
We pressure test at 100 psi, run the camera one last time, and confirm flow. Then we patch the access points with concrete patch mix, match the surface as closely as we can, and walk you through what we did. Total time on site is usually six to nine hours.
STEP 01Locate and scope
We start with acoustic listening devices and a RIDGID SeeSnake video camera to confirm exactly where the failure is and how far the corrosion runs. Thermal imaging cameras from FLIR pick up hot spots on the floor that point to a supply-side leak. This stage usually takes 60 to 90 minutes, and it tells us whether lining is the right call or whether the pipe is too far gone.
Tools & methods
Tools and methods we use on every job
RIDGID SeeSnake video camera
Records the inside of the pipe so we can measure corrosion, find the failure, and show you exactly what we are looking at before we quote.
Acoustic listening devices
Picks up the sound of water escaping under concrete to confirm an active slab leak before we cut anything.
FLIR thermal imaging cameras
Reads hot spots on the floor to separate supply-side leaks from drain issues and narrow the repair to one run.
LeakTronics electronic leak detection equipment
Pinpoints the leak location to within a few inches, which keeps access points small and the lining run short.
Pressure testing gauges
Holds the lined pipe at 100 psi to prove the seal before the concrete goes back. No test, no patch.
Concrete saws and jackhammers
Cut clean 18-inch access openings through reinforced slab without over-breaking the surrounding floor.
Problems we solve
Problems epoxy pipe lining solves for Victoria homes
Most of the calls we get start with one of these four symptoms. Each one points to a failing under-slab line, and each one gets worse the longer it sits.
Ask a pro →Water bill jumped with no visible leak
We use acoustic listening devices and thermal imaging cameras to pinpoint the leak, then line the run so the loss stops at the source. Most homeowners see the bill normalize on the next cycle.
Warm spots or damp patches on the floor
We confirm which side of the system is leaking, isolate the run, and line the failing section. The floor dries out, the hot spot disappears, and the slab stays intact.
Recurring pinhole leaks in copper
We camera the full run and line it end to end instead of chasing individual pinholes. One repair, one cure, and the corrosion cycle stops because there is no bare copper left.
Cast iron drain backups in older homes
We camera the drain, clear the blockage, and line the pipe to restore a smooth interior wall. Flow returns to normal and the joints stop leaking into the soil under the slab.
We pull an epoxy-saturated liner through the existing pipe, inflate it against the walls, and cure it with heat until it hardens into a new pipe inside the old one. The whole process takes three to six hours of cure time on a typical residential run. We then pressure test at 100 psi and run a camera through to confirm the seal before patching the access points.
It is the same trenchless repair, described by what it leaves behind: a bonded epoxy coating on the inside wall of your existing pipe. The coating seals pinholes, bridges small cracks, and shields the metal from the aggressive water chemistry common in Victoria County. Once cured, it is a structural liner, not a paint-on product, and it carries full line pressure.
Typical 2026 pricing in this area runs $4,000 to $12,000 for a residential under-slab run, depending on length, pipe diameter and access. A short 15-foot kitchen branch sits near the bottom of that range; a 60-foot main with two access points sits near the top. We quote a flat number after scoping, so you know the total before we cut concrete.
Yes, for most under-slab copper, cast iron and galvanized lines that are still structurally intact. It is the right call when corrosion is spread along the run rather than isolated to one joint. If the camera shows a collapsed pipe or a run that is more than 60 percent blocked, we tell you straight and quote a replacement instead.
Ready when you are
Get epoxy pipe lining Victoria TX quoted today
Our phone line connects you with providers working Victoria County seven days a week. Call and we will scope the line, give you a flat price, and tell you whether lining or replacement is the honest answer. Same-day estimates, no charge.
Book a Free Estimate 83157330144 →
Request an appointment
Contact SlabFix Repair
Call us at 831-573-30144 any time, day or night. We answer emergency calls 24/7 and schedule standard appointments Monday through Friday. If you're not sure whether you have a slab leak, call anyway and we'll help you figure out the next step.